Omni-directional automatic lifting working lamp Raised and lowered floodlight working lamp Automatic lift lighthouse Item NO.: 1947141

Please contact customer service

Scope of application

 

SFW6110B omnidirectional automatic floodlight work lamp, to meet the needs of large area and high brightness lighting in the workplace at night.

 

The composition

SFW6110B omni-directional automatic floodlight working lamp: it is composed of lighting parts, pneumatic lifting parts, generator parts, control parts and walking support parts.

(a) the lighting element is mainly fixed on the lamp disc, equipped with a 4,500-watt lamp, which can be moved up and down and left and right, and can be simply removed and adjusted to achieve large-area multi-angle lighting;

(2) the pneumatic lifting rod assembly adopts three-level high-strength aluminum alloy lifting rod, with the maximum lifting height of 4.5m.

The main technical parameters of the lamp mast assembly are:

1. Minimum height :1.25 m;

2. The maximum lifting height is 4.5 meters, 6 meters can be configured;

3. Rise time :38 seconds;

4. Descent time :20 seconds;

It weighs about 16 kilograms.

(3) the generator components adopt the EC2500Cx2 Honda generator. When the generator is the power source, the unit can work continuously for up to 13 hours after filling up with fuel.

The main technical parameters of generator components are:

1. Rated output voltage 220 volts /50 hz;

2. The generator can work continuously for 13 hours after filling up with fuel;

3. Overall dimension :5903035mm

4. Start mode: manual start, electric;

5. Type: four-stroke air-cooled type;

6. The noise level of 7 meters is less than 65 db;

7. The generator parts are about 65 kg.

(iv) the control module is composed of wireless remote control and receiving system to control the opening and closing of each lamp within a range of 50 meters;

(5) universal wheel is used for walking support parts, which can be easily moved on uneven gravel road surface, or track wheel can be installed according to user needs to meet the requirements of track operation, convenient and safe; The tripod can be selected according to the specific usage of the user to meet the separation of generator and lamp components.

 

Technical parameters

Rated voltage AC220V

Light source type iodine tungsten lamp

The light bulb

Lamp holder power 4x500W

Lamp holder flux 4x10000LM

The average service life of a light bulb is 3,000 hours

Rated output voltage AC220V

Rated output power :2KW

Rated tank capacity is 15L

 

Continuous working time

Refueling for 13 hours

The electricity was on for a long time

The lifting time of telescopic cylinder is 45 seconds

The maximum lifting height is 6000/4500mm

Minimum height :1800 mm

The overall size

Lamp disc size 380x395 mm

Generator set size 800x500x650mm

The weight of the

Light panel 8 kg

Telescopic tube 11KG 45KG

 

Usage:

(1) push the product to the workplace for smooth placement, press the locking device of two universal wheels to ensure no rolling;

Lift cylinder vertically placed, tighten the manual screw;

(3) put the light disc on the lowest horizontal shaft of the lifting cylinder, tighten the locking screw and adjust the direction. Then connect the air plug with the air socket of the light disc, tighten the screw, and insert the power plug of the cylinder into the generator socket;

In addition, check whether the generator load switch is placed on the closing gear;

5. Generator grounding wire should be reliably grounded in rainy and humid environment;

Check engine oil level, the steps are;

A) open the oil inlet cover and clean the oil plug with A clean cloth;

B) fill the filling port with oil. There is no need to rotate the plug. If the oil level is lower than the lower limit of oil sensor, oil filling is required.

C) fill with oil at the oil plug level, pay attention to adding four-stroke oil. Do not use impure four-stroke oil or two-stroke oil, otherwise it will shorten the service life of the generator;

D) tighten the oil plug.

· check the oil level, if 93# gasoline is too low, fill it up and install the oil cap;

Check the air filter to make sure it is clean.

'when taxing, put the fuel valve in the position, the throttle lever is in the critical position when starting the cold engine (the throttle lever is not in the "off" (off) position when starting the engine); Place the engine switch in the "on" position, gently pull the starting handlebar until resistance is present, and then pull hard. After starting, don't let the handlebars spring back, but gently put it back. When the engine heats up, pull the choke back.
Start the generator, and then turn on the output load switch of the generator;

Insert the power plug into the pump, keep the lamp pole up to the highest level, and shut down after 5-10 seconds;

Use the remote control to switch two lights every time;

When the job is done, press and hold the manual ai